Solvent effects on chemical composition and optical properties of extracted secondary brown carbon constituents

Abstract Brown carbon (BrC) aerosol is an important contributor to positive radiative forcing on Earth, but its influence on the global radiative budget remains uncertain due to the limitations of current analytical methods used to characterize its optical and chemical properties. While online optical instruments provide in situ characterization of BrC light-absorption properties, the wavelengths are often limited due to the light source of optical instruments. Offline measurements can cover the entire UV–Vis wavelength range, but the use of solvents may introduce artifacts. In this study, we compared the mass absorption coefficients at 375 nm (MAC375) measured by online and offline instruments for aerosol samples generated from the nighttime oxidation of heterocyclic volatile organic precursors. Offline samples were extracted with both acetonitrile (ACN) and methanol (MeOH) to investigate the potential solvent effects on the Ångström absorption exponent and BrC chromophores. Our results indicated considerable variations between MeOH-extracted samples and ACN-extracted samples, with pyrrole SOA being especially susceptible to solvent effects. Multi-instrumental analysis confirmed that MeOH could induce solvent artifacts by reacting with conjugated carbonyl chromophores, such as phthalic anhydride, maleic anhydride and maleimide, and subsequently modify the light absorption properties of BrC constituents. Our findings highlight the importance of methanolysis in the formation of artifacts, whereas an inert solvent such as ACN would be ideal for proper characterization of BrC chromophores. Consequently, the results from offline analysis using MeOH as the solvent should be interpreted with caution. Copyright © 2022 American Association for Aerosol Research


Introduction
Brown carbon (BrC) aerosols are light-absorbing organic aerosols that absorb tropospheric solar radiation in the near UV and shorter visible ranges. BrC aerosols are one of the main uncertainties in radiative forcing in the atmosphere. Previous model studies showed that the direct radiative effect of BrC absorption ranges from þ0.10 to þ0.55 W m À2 (Feng, Ramanathan, and Kotamarthi 2013;G. Lin et al. 2014;Zhang et al. 2020). The Community Atmosphere Model simulation also suggested that BrC may reduce the global coverage of low clouds and hence indirectly decrease the cooling effects of clouds (Brown et al. 2018). However, evaluation of BrC's climate forcing is largely limited due to the absence of chromophores in the current models (Laskin, Laskin, and Nizkorodov 2015), which requires in-depth characterization of BrC constituents and their optical properties.
Online analysis (e.g., photoacoustic spectrometer coupled with the cavity ring down extinction spectrometer [PA-CRD-S] and broadband cavity-enhanced spectrometer [BBCES]) is an approach to directly measuring BrC's optical properties such as absorption coefficient, Ångstr€ om absorption exponent (AAE) and the complex refractive index (RI) (Bluvshtein et al. 2016;Bluvshtein et al. 2017;Li et al. 2020). However, online measurements are limited to several wavelengths or even one wavelength, therefore limiting their ability to explore full spectral dependence of light absorption. In addition, online measurements cannot identify chromophores in BrC aerosols, and hence can hardly guide the parameterization of BrC chemistry in climate models independent of complementary composition measurements. Alternatively, offline analysis can acquire not only spectral light absorption but also chemical compositions of BrC. For example, high performance liquid chromatography coupled with a diode array detector and electrospray ionization high-resolution mass spectrometry (i.e., HPLC-DAD-ESI-HRMS) may isolate the BrC constituents and measure their spectral light-absorption as well as chemical formula. This technique has been applied to identify chromophores in several previous investigations (Hettiyadura et al. 2021;Jiang et al. 2019;Lin et al. 2016Lin et al. , 2017Lin et al. , 2018. Additionally, when combined with measurements of organic mass, HPLC-DAD-ESI-HRMS and ultraviolet-visible (UV-Vis) spectrophotometry can be used to estimate mass absorption coefficient (MAC) and AAE (Hettiyadura et al. 2021;Jiang et al. 2019;Lin et al. 2017;Xie et al. 2019). Thus, offline analysis is critical to improving our understanding of BrC formation and evolution.
Each constituent in BrC has a unique solubility in different solvents. Because offline analysis is based on solvent extraction of BrC constituents, it may lead to less accurate results when compared with the in situ measurements carried out by online analysis. The selection of solvent can be a determining factor for the quality of offline analysis. Methanol (MeOH) in particular has been widely used in both experimental and field studies Y.-H. Lin et al. 2014;Liu et al. 2013;Shen et al. 2017;Song et al. 2019;Yan et al. 2020). This is primarily because MeOH performs exceptionally well in terms of extraction efficiency of oxygenated compounds. In experimental studies, Chen and Bond proposed that MeOH could extract over 92% of the organic constituents in BrC aerosols from wood combustion (Chen and Bond 2010), whereas Updyke et al. demonstrated that MeOH could completely extract the organic constituents in secondary BrC aerosols generated from reactions between ammonium and daytime SOA (Updyke, Nguyen, and Nizkorodov 2012). In field studies, Cheng et al. reported that $85% of organic mass in ambient aerosols in Beijing could be extracted by MeOH (Cheng et al. 2016), while Yan et al. (2020) reported that the MeOH-soluble organic components in their aerosol samples could reach up to 93%. Although MeOH-insoluble BrC may be a significant contributor to light absorption of aerosols in some cases (Bai et al. 2020), most studies have proposed offline optical properties and chemical compositions of BrC aerosols based on MeOH extraction.
However, MeOH may induce artifacts that alter the aerosol compositions. Walser et al. (2008) reported that methylation could occur on MeOH-extracted aerosol samples from ozonolysis of limonene. Bateman et al. (2008) further explored the artifacts and concluded that MeOH can react with carbonyl constituents in aerosols and generate new compositions including ester, acetal and hemiacetal in the extracted samples. Kristensen and Glasius (2011) also observed that some of their investigated carboxylic acids (pinonic acid and adipic acid) could generate methyl esters after MeOH extraction but remained intact after acetonitrile (ACN) extraction. Thus, it is uncertain whether the possible solvent-analyte reactions in MeOH may also change the optical properties of extracted BrC samples. Previous studies have suggested that ACN may be a better choice for extracting aerosol constituents because it is an aprotic and inert solvent (Bateman et al. 2008;Kristensen and Glasius 2011;Walser et al. 2008), and it has also been utilized in offline analysis of BrC samples (Lin et al. 2015;Nguyen et al. 2013;Trofimova et al. 2019). Given the interplay between solvent solubility and chemical reactivity, it will be important to evaluate the effects of solvents on both light-absorption properties and chemical compositions of BrC samples.
In this study, we compared the offline MAC 375 of the MeOH-extracted and ACN-extracted samples with the online measurements to evaluate the solvent effects on BrC's light absorption. AAE at near-UV and visible regions (AAE 290/400 and AAE 400/600 ) of the aerosol samples extracted by MeOH and ACN, respectively, were also compared to assess the discrepancy in wavelength dependence of MAC due to solvent effects. The wavelength of 375 nm is representative of strong BrC absorption in the near-UV range (Feng, Ramanathan, and Kotamarthi 2013), while the wavelengths of 290, 400, and 600 nm were selected for AAE calculations to describe the spectral dependence of aerosol light absorption following our previous study . FTIR and mass spectrometric analyses were performed to further confirm the changes in functional groups and composition of chromophores due to solvent artifacts. Results from this study seek to provide an improved understanding of BrC characterization and reduce uncertainties in assessing their impacts.

Generation of BrC aerosols
Controlled chamber experiments were performed in a 10 m 3 FEP film chamber under dry condition (RH < 20%) at room temperatures (20-25 C) to produce tested BrC aerosols. The experiments were conducted in dark condition to simulate nighttime oxidation of heterocyclic volatile organic compounds (VOCs) in the presence of NO 2 and O 3 , which has been indicated as a secondary source of BrC aerosols . NO 3 radicals were generated via the reactions between NO 2 and O 3 , with the initial concentration ratio of [NO 2 ]/[O 3 ] being around 0.1 or 0.3 that are similar to the conditions observed in fresh wildfire plumes (Singh et al. 2010). O 3 was generated by flowing $0.4 lpm of pure oxygen through the ozone generator via corona discharge (A2Z Ozone 3 G LAB). The target initial mixing ratio of O 3 was $1500 ppbv. NO 2 was either directly injected with a NO 2 cylinder (4789 ppm, Airgas) to achieve 150 ppbv, or it was generated in the chamber prior to the injection of 1500 ppbv O 3 by reactions between NO (150 ppbv) and O 3 (150 ppbv). During the injections of O 3 and NO 2 , $15 lpm of zero air was also injected for 5 min to facilitate mixing in the chamber. This study used pyrrole (TCI America, >99%), 1-methylpyrrole (TCI America, >99%), 2-methylpyrrole (aa blocks, 98%), thiophene (Alfa Aesar, 99%), 2-methylthiophene (Alfa Aesar, 98%), furan (TCI America, >99%), and furfural (Acros Organics, 99%) as model compounds of heterocyclic VOC precursors. After 1 h reaction of NO 2 and O 3 , the heterocyclic VOC precursor was introduced into the chamber by flowing $15 lpm of N 2 over a heated jar containing the VOC liquid sample to achieve a mixing ratio of $200 ppbv in the chamber. Each experiment was duplicated three times, where only one heterocyclic VOC precursor was involved. Aerosol samples for offline analysis were collected on PTFE membrane filters (46.2 mm, 2 mm, Tisch Scientific) from the chamber experiment. Aerosol collection efficiency of our filters was over 99.5%, which was estimated by the ratio of 10-min averaged aerosol volume concentrations ahead of the filter to that behind the filter. Details for sample collection and preparation can be found in our previous study ).

Online aerosol composition and size measurements
Real-time size-resolved mass distributions and chemical composition of aerosol particles were measured by a mini-Aerosol Mass Spectrometer coupled with a compact time-of-flight mass spectrometer (mAMS, Aerodyne Research Inc.) every 20 s during all experiments (Bahreini et al. 2005). Sensitivity and sizing capability of the instrument were calibrated regularly using dry, size-selected ammonium nitrate particles or dry polystyrene latex spheres. The raw data were analyzed as described previously (Allan et al. 2004). Given the accuracy of the mass calibrations (20 ppm), high-resolution analysis of the raw mass spectra was also carried out for m/z 20-115 amu to calculate the mass concentrations of all species except ammonium (Bahreini et al. 2012). A scanning electrical mobility spectrometer (SEMS, Brechtel Manufacturing Inc.) was used to determine the number concentration and size distribution of SOA from 10 to 800 nm with 140 bins. The sampled air from the chamber passed through a 30-cm-long diffusion dryer filled with silica gel (Sigma-Aldrich) and Purafil (Thermo Scientific) before reaching mAMS, SEMS, and the photoacoustic extinctiometer (PAX, described below). Details of calculations of the organic aerosol fraction (MF OA ), particulate effective density (q eff ), and the total volume concentration of particles used to estimate the SOA mass concentration (C SOA ) are provided in the online supporting information (SI) Text S1. Calculated values are summarized in Table S1. The C SOA was used subsequently to calculate online MAC.

Optical measurements
In this work, both UV-Vis spectra of extracted SOA solution and in situ absorption coefficients of SOA particles were measured. A UV-Vis spectrophotometer (Beckman DU-640) was used to measure the UV-Vis absorbance in the range of 290-700 nm, with the reference wavelength at 700 nm. Before the sample scanning, blank filters extracted by either solvent (MeOH or ACN) were used as spectral blanks, in which no absorption spectra were observed. Each sample was scanned three times, and the average spectra were used for calculating offline MAC profiles, AAE 290/400 and AAE 400/600 . The offline imaginary RI (k offline ) was calculated using Equation (1), where q eff is the aerosol effective density, k is the wavelength, Abs solution(k) is the absorption of the SOA solution samples, and C m is the mass concentration of sampled SOA in the solution.
We assumed that all the organic mass could be extracted by both solvents, which would be discussed in Section 3, so C m was calculated based on the flowrate and the average mass concentration of SOA during the sampling, using the organic mass fraction of the aerosols and overall effective densities corresponding to the start of filter collection. The uncertainty of MAC 375 will be discussed in Section 3. AAE 290/400 and AAE 400/600 were calculated by the power-law dependence of light absorption on the wavelengths (Equation (2)).
In situ measurements of particulate absorption coefficients at 375 nm (b abs,375 ) were performed by a PAX (Droplet Measurement Technology) at 1 Hz (Dingle et al. 2019). Since the absorption measurements were averaged to the scan time of SEMS, the detection limit was defined as two times the standard deviation of the 1-Hz absorption measurements when sampling filtered air, scaled down by ffiffiffiffiffiffiffi 140 p s. Online MAC at 375 nm is calculated by Equation (3), where the C SOA calculation is described in the SI Text S1.
For comparison, MAC offline (375) was calculated using Equation (4), where b abs,Mie-converted (375) is the particle-relevant value of light absorption coefficient at 375 nm converted by the Mie theory calculations based on k offline , as described by Liu et al. (2013).
The size distribution of aerosols ( Figure S1) was considered during the conversion, and the real RI was set as 1.4 based on our previous work . For simplicity, MAC online (375) will be denoted as "MAC 375,online " while the Mie-converted MAC offline (375) corresponding to MeOH and ACN extraction will be denoted as "MAC 375,MeOH " and "MAC 375,ACN " hereafter.

Functional group analysis
Functional group analysis of on-filter and solventextracted samples was performed using attenuated total reflectance Fourier-transform infrared spectroscopy (ATR-FTIR) measurements (Thermo Nicolet 6700). On-filter samples were measured by being attached to the ATR platform, while extracted samples were concentrated to around 50-100 ll with a gentle flow of nitrogen and dropped on the crystal window of the ATR platform. Each sample was dried for 3-5 min on the ATR platform before measurements. All the measurements were performed with 0.5 cm À1 resolution and 128 scans over 700-4000 cm À1 . The acquired IR spectra were analyzed using Igor Pro 7 (WaveMetrics, Lake Oswego, OR, USA). Spectral deconvolution was performed with the Gaussian profiles that were widely used in previous ATR-FTIR studies (Branca et al. 2016;Ortuso et al. 2019;Srour et al. 2017). To smooth the IR spectra, the Savitzky-Golay algorithm (Savitzky and Golay 1964) was used with a 21-point window and the second order formulation (Sve cnjak et al. 2015).

Chemical composition analysis
Multi-instrumental analyses were performed to identify chromophores that can react with MeOH and characterize their artifact products, including (1) gas chromatography-electron impact mass spectrometry (GC/ EI-MS, Agilent Technologies 6890N GC System and 5975 inert XL Mass Selective Detector), (2) liquid chromatography coupled with a diode array detector, an electrospray ionization source and a quadruple-time-offlight mass spectrometer (LC-DAD-ESI-Q-TOFMS, Agilent Technologies 1260 Infinity II and 6545 Q-TOF LC/MS), and (3) time-of-flight chemical ion mass spectrometry implemented with the Filter Inlet for Gases and AEROsols system (FIGAERO-ToF-CIMS, Aerodyne Research Inc.). The identified chromophores were quantified by the peak integration of the corresponding extracted ion chromatogram (EIC) from the GC/EI-MS data. Operational procedures of GC/EI-MS and LC-DAD-ESI-Q-TOFMS are modified from our previous study , and the technical details in this study are available in the SI Text S2 and S3.
FIGAERO-ToF-CIMS was used as in situ characterization of chemical compositions and provides a complementary support of compositional analysis. The temperature profile for aerosol collection, desorption, and analysis was as follows: (1) sampling aerosols for 25 min at room temperature, (2) linearly increasing the temperature from 30 C to 200 C in 25 min, (3) holding at 200 C for 15 min, and (4) cooling to 30 C in 20 min. In our experiments, both negative and positive modes were used for ion detection, where iodide ion (I -) or proton (H þ ) were the adduct ions for soft ionization. In the negative mode, Iwas produced by flowing $2.5 lpm of N 2 through a permeation tube containing CH 3 I followed by a 210 Po ionizer. Water vapor was also introduced to the ion-molecule reaction (IMR) chamber of ToF-CIMS by flowing $1 lpm of N 2 through a bubbler containing deionized water. In the positive mode, (H 2 O) n H þ clusters were produced by flowing $2.5 of lpm N 2 through the bubbler followed by the 210 Po ionizer. The proton of the (H 2 O) n H þ clusters may transfer to the analytes during ion-molecule collisions, which generates the H þ -adduct ions. Since soft ionization has selectivity for product detection, negative mode was tuned by 1,2-dinitrobenzene and 2nitrophenol, while positive mode was tuned by furan and furfural. Both modes were tuned with the target resolution power of $4000. The single ion measurement value was $2.1 mVns for $3000 scans, and the operating pressures of each part in the TOF-CIMS are listed in Table S2.

Comparisons of online and offline lightabsorption properties
Direct comparisons between online and offline MAC 375 are presented here to evaluate the solvent effects on BrC's light-absorption properties ( Figure 1 and Table S3). Online MAC 375 is used as an in situ benchmark for offline MAC 375 . Figure 1 shows that solvent extraction can cause different levels of deviation in MAC 375 when compared to online measurements. Among the SOA systems studied, pyrrole SOA is most sensitive to the solvent effects at the absorption wavelength of 375 nm. The discrepancies in light-absorption properties between MeOH-extracted and ACN-extracted SOA were also evaluated by offline AAE 290/400 and AAE 400/ 600 (Figure 2 and Table S4), which represent the change in MAC along with wavelengths in the UV and visible ranges, respectively. Although online AAE is not available as an in situ benchmark, comparisons of offline AAE in different solvents by linear regression (with intercept set to 0) can still reveal the disparity in wavelength dependence of MAC due to solvent effects. Figure 2a shows that MeOH extraction tends to cause lower AAE 290/400 than ACN extraction (y ¼ 1.27x), while a strong correlation coefficient (R ¼ 0.78) suggests a roughly consistent trend of AAE 290/400 for MeOH-extracted and ACN-extracted samples. In contrast, Figure 2b shows high variability of AAE 400/600 for MeOH-extracted and ACN-extracted samples, with a slope close to 1 but a moderate correlation coefficient (R ¼ 0.41), revealing the inconsistency of wavelength dependence of MAC in the visible range due to solvent effects. As a result, the effect of solvents may cause considerable uncertainties based on AAE assessments, complicating the offline evaluation of BrC's MAC profiles.
The solvent effects on BrC's light-absorption properties have been hitherto revealed based on MAC 375 and AAE, where MeOH and ACN extractions led to divergent results. From a chemical perspective, although MeOH and ACN are both polar solvents, their polar functional groups are distinct, with MeOH having a hydroxyl group and ACN having a nitrile group. Because the differences in polar functional groups can result in selective solubility of analytes, the extracted BrC chromophores in MeOH and ACN may vary. Notably, because the extraction efficiency of each solvent varies for different compounds (Lanzafame et al. 2021), it is challenging to accurately determine the extraction efficiency for the SOA system as a whole. The offline MAC 375 reported here may be underestimated due to a lack of consideration for extraction efficiency. Furthermore, as a polar protic solvent, the hydroxyl group of MeOH may enable proton transfer reactions leading to esterification, whereas the nitrile group of ACN is a very stable and considered as an inert functional group during extractions (Bateman et al. 2008). As a result, possible MeOH-analyte interactions may cause artifacts in MeOH-extracted samples and interfere with MAC profiles. Notably, in addition to solvent selectivity and the formation of artifacts in offline analysis, discrepancies between online and offline MAC 375 may be partially attributed to other uncertainties. Sun et al. (2007) reported that in the small particle regime (i.e., particulate diameter much smaller than the wavelength of light), particulate effects should be considered in the estimation of MAC via a coefficient, which is a function of both the real part (n) and the imaginary part (k) of the complex RI. Several reviews of BrC optical properties also discussed the potential interference in MAC owing to particulate effects (Laskin, Laskin, and Nizkorodov 2015;Moise, Flores, and Rudich 2015;Saleh 2020). Since Mie theory calculations were performed to estimate MAC 375,MeOH and MAC 375,ACN , we expect minimal particulate effects in our case. In addition, solvent environments can induce extra interference in the UV-Vis spectra of BrC chromophores by perturbing the excitation wavelengths and full width at half maximum (FWHM) of spectral peaks (Benassi et al. 2014;Chen et al. 2020). This may also contribute to the uncertainty of offline MAC 375 , which should be explored in future studies.

Functional group analysis of solvent-extracted BrC samples
To analyze the compositional difference between MeOH-extracted, ACN-extracted and in situ SOA samples, ATR-FTIR spectra were first measured to reveal the compositional fingerprints as well as confirm the presence of key functional groups in SOA constituents. Peak assignments were based on a review of IR studies conducted on organic aerosols (Cao et al. 2018). Figure S2 provides an example for the technical details of spectral deconvolution.
Our results show that different treatments of SOA samples can result in divergent fingerprints within the spectral range of 1000-1500 cm À1 (green shaded area in Figure 3). For example, the on-filter spectrum of pyrrole SOA formed at [NO 2 ]/[O 3 ] ¼ 0.1 condition shows two sharp peaks with a rather flat spectral profile at other wavenumbers in the shaded area. However, both MeOH-extracted and ACN-extracted spectra reveal a similar pattern of three spectral profiles spread in the shaded region. The differences between on-filter and solvent-extracted spectra indicate that the ratios of functional groups are altered during solvent extraction. In addition, the ACNextracted spectrum has more split peaks than the MeOH-extracted spectrum in the shaded area ( Figure  3a), revealing that extraction by different solvents can lead to inconsistent compositions.
Nevertheless, the ATR-FTIR measurements of functional groups also provide valuable insight into the composition of SOA systems (Chen et al. 2016;Russell, Bahadur, and Ziemann 2011;Yu et al. 2018 (Figures 3a and b), while peaks at adjacent wavenumbers (865 and 850 cm À1 ) were also observed in all thiophene SOA spectra (Figures 3c and d). These peaks correspond to C-H bending on aromatic rings and alkene chains, suggesting the prevalence of conjugated systems in the SOA samples investigated. Similarly, carbonyl groups (characterized by C ¼ O stretching in the 1600-1800 cm À1 range) are ubiquitous in all SOA samples investigated (Figure 3 and Figure S3). These results can serve as references for further analysis of chemical compositions in nighttime BrC from heterocyclic VOC precursors.

Identification of solvent-analyte reactions
To unravel more mechanistic insights of solvent artifacts in MeOH extraction, further characterization of chromophores and their artifact products was performed by combining multiple instruments. Since our ATR-FTIR measurements confirmed the presence of carbonyls and conjugated systems, the identification of solvent-analyte reactions was focused on conjugated carbonyls. Our analysis identified the artifact products from three conjugated carbonyl compounds: phthalic anhydride, maleic anhydride, and maleimide. All of these compounds were identified in ACN-extracted SOA samples by GC/EI-MS (Figures 4a-c). The identities of these compounds in SOA samples were initially proposed by the NIST library based on the spectral match of their electron ionization (EI) mass spectra, and subsequently confirmed by their authentic chemical standards (Figures 4d-f). In situ analysis of SOA constituents using FIGAERO-ToF-CIMS also confirmed the presence of identified compounds ( Figure S4). The UV-Vis spectra of these compounds in ACN proved that they are BrC chromophores ( Figure S5). To characterize the artifact products, chemical standards of the identified chromophores were dissolved in MeOH and measured by GC/ EI-MS. The NIST mass spectral library was used to determine the structures of artifact products. Our results showed that dimethyl phthalate (Figure 4j) was detected in the MeOH solution of phthalic anhydride standard, whereas dimethyl fumarate and dimethyl maleate (Figure 4k) were detected in the MeOH solution of maleic anhydride standard. The presence of these artifact products in extracted SOA samples was also confirmed by the labeled peaks in Figures 4g and h. Since SOA samples are mixtures of different constituents, other analytes may also generate ion fragments at tm/z 163 and 113, leading to the extra peaks ( Figure 4g) or altering the shape of the peaks ( Figure  4h) in the EICs. In the MeOH solution of maleimide, an artifact peak was detected ( Figure S6a), but it is challenging to determine its formula and structures because the NIST mass spectral library could not offer a tentative result with a high probability. As a result, we only reported its mass spectrum in Figure S6b. In addition, we found that all of the artifact products discussed above could be detected immediately by GC/ EI-MS once the chemical standards of BrC chromophores were dissolved in MeOH, showing the SOA composition could change rapidly during MeOH extraction. Pacher et al. (2010) have previously reported that imide may undergo methanolysis in the MeOH solution under room temperature. The methanolysis product of maleimide is expected to be produced during the MeOH extraction process, which should have a Figure 3. ATR-FTIR spectra corresponding to the BrC SOA samples. MeOH-extracted spectra are in red, ACN-extracted spectra in blue, and on-filter spectra in brown. Green shaded areas highlight the divergent fingerprints in the 1000-1500 cm À1 range.
MeOH-added formula (i.e., C 5 H 7 NO 3 ). Because GC/ EI-MS did not show results for C 5 H 7 NO 3 , LC-DAD-ESI-Q-TOFMS was used to probe the C 5 H 7 NO 3 in the MeOH solution of maleimide. The EIC of C 5 H 7 NO 3 Na þ shows three peaks (Figure 4l), suggesting the presence of three isomers of the formula C 5 H 7 NO 3 , while Figure 4i also confirms their presence in methanol extracted SOA samples. Notably, Figures 4i and l show different relative intensities among these peaks, suggesting that the artifact products may further react with other analytes in the SOA samples, or other SOA constituents with the same formula (i.e., C 5 H 7 NO 3 ) may exist.
Based on our experimental characterizations, the mechanisms leading to formation of artifacts are proposed in Figure 5. The proposed products in Figures  5a and b are based on the candidate compounds with the highest matching score identified in GC/EI-MS by the NIST library, which also agree with previously described methanolysis mechanisms for phthalic anhydride and maleic anhydride (Eliel and Burgstahler 1949;Sutton, Reed, and Hiles 2003). Our GC/EI-MS analysis detected all four artifact products once maleic anhydride was dissolved in MeOH ( Figures S7a and b), showing that the amount of intermediate products from methanolysis decreased ( Figures S7a and c) while further esterification products increased (Figures S7b and d) over time. Similarly, the proposed products in Figure 5c are derived from the molecular formula identified by LC-DAD-ESI-Q-TOFMS and the reported methanolysis mechanism of cyclic imides (Kavitha et al. 2016). While methanolysis is expected to form two products, the maleimide artifacts have three peaks, suggesting that other pathways may also be involved. One possibility is that the hemiacetal could be generated from direct addition of MeOH to the carbonyl group, as proposed by Bateman et al. (2008). Notably, GC/ EI-MS and LC-DAD-ESI-Q-TOFMS may only identify a subset of artifact products; other artifact reaction pathways in MeOH may occur. In addition, the detected chromophores can contribute to solvent artifacts in most of our SOA samples (Table 1); however, chromophores capable of initiating artifact products in thiophene SOA and 2-methylthiophene SOA were not identified in the current study due to the limitation of the NIST library or a lack of commercially available chemical standards. Nevertheless, our results highlight that methanolysis may play a significant role in the solvent-analyte interactions that occur during MeOH extraction of SOA samples.
Furthermore, the identified chromophores account for a considerable fraction ($0.1-5.0%) of the total SOA mass in various samples (Table 1), revealing that solvent artifacts may be influential in altering the light-absorption properties of the studied BrC systems. Figure 6 shows that the light absorbance of all three chromophores decreases in MeOH solutions over time within the 290-350 nm wavelength range compared to the same amount of chromophores dissolved in ACN  solutions, indicating that chromophores could continue to react with MeOH and change the light absorbance. At a starting concentration of 100 ng ll À1 , the chromophore molecules could be undetectable ( Figures S8a and b) or largely consumed ( Figure  S8c) as soon as the SOA samples were dissolved in MeOH, indicating that the artifact products could significantly modify the light absorbance at the concentration and time scale relevant to offline SOA analysis. Nevertheless, given the low absorbance of identified chromophores at 375 nm ( Figure 6 and Figure S5), other artifact products may also exist and contribute to the deviation of MAC 375 in Figure 1. Indeed, the solvent effect is a multifactorial interference in the light-absorption properties of BrC, where solvent artifact is an important component while other factors in the preceded discussions, such as solvent selectivity and perturbation on molecular spectral absorptivity due to solvation of chromophores, can also contribute to the change of light absorption of the BrC samples.

Conclusions
This study compared the differences between online and offline MAC 375 , revealed the discrepancy of AAE between MeOH-and ACN-extracted SOA samples, and identified the chromophores that may generate artifacts in MeOH-extracted BrC samples. Our results indicated that sample extraction with different solvents could not only cause deviations in MAC 375 at different levels but also lead to divergent AAE 290/400 and AAE 400/600 , which requires further comparisons with online measurements of AAE to better evaluate the influence of solvent effects. ATR-FTIR analysis enabled the characterization of ubiquitous conjugated carbonyls in the SOA samples, whereas multi-instrumental analysis revealed that the conjugated carbonyl chromophores, including phthalic anhydride, maleic anhydride and maleimide could generate artifacts in MeOH. These results highlight the importance of methanolysis in the artifact mechanisms; consequently, an inert solvent such as ACN may be more ideal for offline analysis of BrC compositions. Furthermore, the three chromophores discussed in this study are also prevalent in other SOA systems. Maleic anhydride is a product of photooxidation of anthropogenic aromatic VOCs such as benzene and toluene (Bandow, Washida, and Akimoto 1985;Forstner, Flagan, and Seinfeld 1997;Hamilton et al. 2003;Jang and Kamens 2001), and derivatives of maleic anhydride have also been identified in the field aerosol samples (Al-Naiema, Roppo, and Stone 2017). Additionally, Montoya-Aguilera et al. detected maleic anhydride and maleimide in the SOA generated from photooxidation of indole (Montoya-Aguilera et al. 2017), and several studies have reported phthalic anhydride as a product of daytime oxidation of PAHs (Al-Naiema and Stone 2017; Chan et al. 2009;Jang and McDow 1997;Kautzman et al. 2010). Notably, maleic anhydride and phthalic anhydride have been widely observed in ambient aerosols from biomass burning plumes or fuel combustion (Al-Naiema, Roppo and Stone 2017; Al-Naiema and Stone 2017; Bruns et al. 2017;Gao et al. 2022;Jeon et al. 2019;Oyama et al. 2016). All these studies support that the MeOH-extraction artifacts observed in our study are expected to affect the characterization of BrC Figure 6. Changes in UV-Vis spectra of MeOH-dissolved (solid line) and ACN-dissolved (dash line) chromophore solutions over time for (a) phthalic anhydride, (b) maleic anhydride, and (c) maleimide standards. The UV-Vis spectra were measured at 0, 4, 24, and 48 h after the dissolution of chromophore standards in MeOH. For each chromophore, the starting mass concentrations in both solvents were the same. composition and optical properties from various primary and secondary sources. In addition, dimethyl phthalate is a globally distributed pollutant confirmed by solvent-free characterization of ambient aerosol compositions ; extraction of SOA samples with MeOH is expected to affect the quantification of dimethyl phthalate if phthalic anhydride is also present. Hence, offline analysis using MeOH as the solvent may introduce significant interferences into the SOA compositional analysis.
However, some limitations of using ACN in offline analysis should not be overlooked. Apart from its lower solubility for certain SOA constituents (e.g., carboxylic acids [Bradley et al. 2010]) when compared to MeOH, a previous study has also indicated that a trace amount of water in ACN in the extracted SOA samples is capable of hydrolyzing some reactive functional groups such as organic hydroperoxides . Moreover, since ACN and MeOH are both polar solvents, nonpolar chromophores that cannot be extracted could be underestimated. Overall, our study demonstrated that offline results of BrC light absorption should be interpreted with caution and carefully used in modeling studies.